CVE-2024-42815

In the TP-Link RE365 V1180213, there is a buffer overflow vulnerability due to the lack of length verification for the USERAGENT field in /usr/bin/httpd. Attackers who successfully exploit this vulnerability can cause the remote target device to crash or execute arbitrary commands...

CVE-2024-42815

TP-Link RE365 V1_180213 is affected by CVE-2024-42815 due to a buffer overflow in /usr/bin/httpd arising from insufficient length verification of the USER_AGENT field. This can allow remote attackers to crash the device or execute arbitrary commands. The vulnerability is widely reported across mu...

CVE-2024-42812

In D-Link DIR-860L v2.03, there is a buffer overflow vulnerability due to the lack of length verification for the SID field in gena.cgi. Attackers who successfully exploit this vulnerability can cause the remote target device to crash or execute arbitrary commands...

Recommended Install Order for Preparing Target Device Captured by Provisioning Server to Deploy vDisk

This article contains the recommended order to install or prepare a target device that must be captured by the Provisioning Services Sever to deploy a virtual disk...

XenApp Target Device Does Not Respond and Displays a Gray Screen

XenApp Target Device appears to be unresponsive. Background When the Provisioned XenApp server is accessed through the local console, you see a gray blank screen. There are different symptoms reported for the same incident and they are not specific to Provisioning services or XenApp. In some case...

Targets Booting Very Slowly - Windows Splash Seen for over 10 Minutes

New deployment targets taking over 10 minutes to boot. Background Target device gets to the Windows splash and then it takes over 15 minutes to load Windows. After Windows loads, there is no performance problem...

Provisioned Target Device Booting up with Multiple IP Addresses

Provisioned Target Device booting up with multiple IP addresses...

How to Capture a Network Trace for a PVS Target Device

This article describes how to capture a target-side network trace from a Provisioned Services PVS machine. Requirements Hypervisors: XenServer 5.x XenServer 6.x VMware ESX 4.x VMware ESXi 5.x Hyper-V 2012 Or Physical Environment including but not limited to HP/IBM/Dell/Cisco target devices...

Error: "vDisk is not available. Please check your network PXE boot configuration and restart Imaging Wizard" or "Red X" on Provisioning Server

After installing the Target Device Software and rebooting the following symptoms can be seen: A Red X is displayed on top of the vDisk Status Applet in the Tray Bar After running the Imaging Wizard and rebooting the following message is shown:"vDisk is not available. Please check your network PXE...

Provisioning Services Target Device Fails to Download tsbbdm.bin

Booting a Provisioning Services PVS target device through the Boot ISO method created by the Boot Device Manager utility fails with the following error: "Downloading tsbbdm.bin from FAILED!"...

How to Image a Target Device Using the Imaging Wizard

This article describes how to image target device using the Imaging Wizard. Prerequisites Enable Windows Automount on Windows Enterprise Server operating systems. Disable Windows Autoplay. Remove any virtualization software before performing a conversion. Verify adequate free space exists on the...

Blue Screen with Error Code 0x0000007B When Booting a Target from a vDisk Using Target Device Software 6.x or 7.x

When booting a Target from a vDisk using Target Device Software 6.x or 7.x, you might get a Blue Screen with error code 0x0000007B and the following error description: “ERROR: SOCKET…” The error description will contain additional values as shown in the following screen shot:...

How to Prepare Provisioning Services 7.x Master Target Device to be Captured on a vDisk

This article provides the recommended procedure for preparing Provisioning Services 7.x Master Target Device to be captured on a vDisk...

DHCP configurations for PVS

Citrix recommends DHCP configuration which ensures that a PVS target device receives the same IP address for all DHCP requests during its booted lifespan. The end result should be a target device using the same IP address it received at boot time, for the entirety of its booted lifespan. DHCP...

Citrix Provisioning - Converting An Existing vDisk From BIOS To UEFI

Converting an existing BIOS vDisk into UEFI vDisk for future PVS Target Device support...

PVS | Error Id: XDDS:A6D8C1E7 - Unable to add Target Device to Catalog

Attempting to add Target Devices will return the following error: "The virtual machine with Mac Address in the selected Device Collection could not be found in any available connection". In View Details the following information is present: Error Id: XDDS:A6D8C1E7 Exception: DesktopStudioErrorId ...

GHSA-7VFX-HFVM-RHR8 cordova-plugin-fingerprint-aio DoS vulnerability

Summary: Sending a specially crafted intent with an invalid/empty extras de.niklasmerz.cordova.biometric.BiometricActivity can cause the app to crash. sending the intent repeatedly can prevent the app using this plugin from working, resulting in a denial of service DoS condition. Impact A 3rd par...

PVS Target Device Stuck at "Applying Computer Settings"

Provisioning Services PVS target device fail to boot. The target device stuck at applying computer settings stage and then trigger restart...

"The network logon service was not started" when logging onto PVS Target Device via Console

When logon PVS Target Device TD via console, it throws below error: "An attempt was made to logon but the network logon service was not started." TD VDI is unregistered status in Citrix Studio...

CVE-2023-4296

​If an attacker tricks an admin user of PTC Codebeamer into clicking on a malicious link, it may allow the attacker to inject arbitrary code to be executed in the browser on the target device...