## SS7 Pentesting Toolkit * * * The toolkit is build upon the [ Osmocom SS7 stack ]() and implements some basic MAP messages. At its current state tests against the [ HLR ]() are ready for use, in future versions tests against [ VLR ]() , [ MSC ]() and [ SMSC ]() will follow. The tool is written in Erlang; to get it running you will need the [ Erlang runtime environment. ]() It is developed for version 17.5. Signalling System No. 7 (SS7) is a set of telephony signaling protocols developed in 1975, which is used to set up and tear down most of the world’s public switched telephone network (PSTN) telephone calls. It also performs number translation, local number portability, prepaid billing, Short Message Service (SMS), and other mass market services. ![SS7 Pentesting Toolkit: ss7MAPer](https://d21ic6tdqjqnyw.cloudfront.net/wp-content/uploads/2016/08/02120102/ss7MAPer.jpg) As you can see in the picture, the demonstrated test cases for the HLR respond to most of the MAP messages regardless the fact that we are not registered as valid provider. The tool is not configured as a serving MSC nor a roaming contractor. Some of the information gathered can be seen as critical, as the MSISD -> IMSI resolution, the over-the-air crypto keys or the ability to create supplementary services e.g. call forwarding. The messages and test cases are gathered from public SS7 research of the last years (see [ 1 ]() , [ 2 ]() ) and check for known weaknesses in the SS7 domain. The tool itself was developed under a cooperation with the Belgium provider [ _ Proximus _ ]() and aims to test the secure configuration of the internal and external SS7 network access. Thanks a lot for giving us the opportunity here, we are convinced that the tool gives the research community but also telecommunication providers a new, important and (especially) open-source-based possibility for SS7 testing. ## Get it running You will need: * Erlang. Get it from your repo or from [ http://www.erlang.org ]() * Rebar. Get it from your repo or from [ https://github.com/rebar/rebar ]() * The code (; git clone https://github.com/ernw/ss7MAPer * The dependencies cd ss7MAPer rebar get-deps * Patch the dependencies cd deps/osmo_map patch -p1 < ../../patches/osmo_map.patch cd ../osmo_sccp patch -p1 < ../../patches/osmo_sccp.patch cd ../osmo_ss7 patch -p1 < ../../patches/osmo_ss7.patch * Get the deps to build (; This is not as easy as it might sound, I needed to: Patch the epacp/rebar.config and replace {port_envs, [ {"DRV_CFLAGS", "-g -Wall $ERL_CFLAGS"}, {"DRV_LDFLAGS", "-lpcap $ERL_LDFLAGS"} ]}. with {port_envs, [ {"CFLAGS", "-g -Wall $ERL_CFLAGS"}, {"LDFLAGS", "-lpcap $ERL_LDFLAGS"} ]}. Another dependency is not covered by rebar, so you need to fetch it manually: cd deps git clone http://cgit.osmocom.org/erlang/signerl/ Build the ASN.1 source files: cd deps/signerl/TCAP/asn_src/ITU make Copy the ASN.1 files to osmo_sccp: cp deps/signerl/TCAP/asn_src/ITU/*rl deps/osmo_sccp/src/ Also the osmo libs have dependencies on each other and some other deps are shared, so I created some symlinks: mkdir deps/osmo_sccp/deps ln -sd ../../osmo_ss7 deps/osmo_sccp/deps/osmo_ss7 ln -sd ../../epcap deps/osmo_sccp/deps/epcap ln -sd ../../pkt deps/osmo_sccp/deps/pkt ln -sd ../../signerl/MAP deps/osmo_sccp/deps/MAP ln -sd ../../signerl/SCCP deps/osmo_sccp/deps/SCCP ln -sd ../../signerl/TCAP deps/osmo_sccp/deps/TCAP mkdir deps/osmo_map/deps ln -sd ../../osmo_ss7 deps/osmo_map/deps/osmo_ss7 ln -sd ../../epcap deps/osmo_map/deps/epcap ln -sd ../../pkt deps/osmo_map/deps/pkt And copy some files in place: cp deps/signerl/SCCP/itu/include/sccp.hrl deps/osmo_sccp/src/ cp deps/signerl/TCAP/include/tcap.hrl deps/osmo_map/src/ * Build the code rebar co ## The config file The config file is split in 4 section, sctp, m3ua, sccp and target. In the _ sctp _ section source and destination ip as well as source and destination port of the SCTP connection are configured. In the _ m3ua _ section all the M3UA parameters, like local and remote point code are configured. In the _ sccp _ section currently only the local (or source) global title needs to be configured. Last but not least in the _ target _ section information about the tested environment need to be configured, like the global title of the HLR, or the MSISDN of the tested phone. Be sure to modify it to your needs. ## Running the tool To run the tool one needs to start a rebar shell: cd ss7MAPer rebar shell Then the SIGTRAN connection needs to be established: Pid = ss7test_app:start(1, "./configfile"). If everything is set up correctly the m3ua connection comes up. To run the HLR tests, simply enter: Pid ! {test_hlr}. [ ![SS7 Pentesting Toolkit: ss7MAPer Download](https://d21ic6tdqjqnyw.cloudfront.net/wp-content/uploads/2016/05/08082805/Download3-1024x154.png) ]()

Source	Link
github	www.github.com/ernw/ss7MAPer
github	www.github.com/rebar/rebar